EVBox · OCPP 1.6J
Not hardware-validated by 22togo Last verified 2026-11-12EVBox Elvi
Connect an EVBox Elvi 22 kW three-phase home charger to 22togo over OCPP 1.6J.
The Elvi uses the EVBox web interface or app. Configure the OCPP Server URL, Charge Point ID, and Authorization Key in Settings → OCPP, then restart and verify in Status → OCPP.
Before you start
- A 22togo station record with its exact identity (Charge Point ID) and OCPP auth token.
- The OCPP server URL shown in the 22togo app for that station (including identity path).
- The charger installed, powered, and connected to the local network (Ethernet or Wi-Fi).
- A computer or phone with web browser on the same network.
Settings to enter
Use these values when configuring the charger's OCPP backend.
| Setting | Value | Notes |
|---|---|---|
| Protocol | OCPP 1.6J |
Select OCPP 1.6 JSON. |
| OCPP Server URL | wss://<ocpp-host>/<identity> |
Use the exact URL from the 22togo app. Must include the identity path segment. |
| Charge Point ID | <identity> |
Must match the 22togo station identity exactly. |
| Authorization Key | <ocpp_auth_token> |
Enter the per-station auth token from 22togo. EVBox Elvi supports this field. |
| Network | DHCP (Ethernet) or Wi-Fi |
Configure Ethernet (DHCP) or Wi-Fi before OCPP settings. |
Setup steps
Follow the steps in order. Restart the charger after changing backend settings.
-
1
Access the EVBox web interface
- Connect to the same network as the charger.
- Open a browser to the charger’s IP address (find via router or EVBox app). 3. Log in with the installer credentials (default: username
installer, password on the label orevbox).
The EVBox Elvi can also be configured via the EVBox app during initial setup.
-
2
Configure network connection
- Go to Settings → Network.
- For Ethernet: ensure DHCP is enabled (default).
- For Wi-Fi: select Wi-Fi, choose your SSID, enter password, and connect. 4. Verify internet connectivity (green status).
EVBox Elvi supports both Ethernet and Wi-Fi. Configure Wi-Fi first if not using Ethernet.
-
3
Configure OCPP settings
- Go to Settings → OCPP.
- Set Protocol to OCPP 1.6J.
- In OCPP Server URL, enter the full 22togo WebSocket URL including identity path (e.g.,
wss://ocpp.22togo.com/CHG-001). - In Charge Point ID, enter the exact station identity from 22togo.
- In Authorization Key, enter the OCPP auth token from 22togo. 6. Click Save.
EVBox Elvi exposes the Authorization Key field. If using an older firmware, update via the app first.
-
4
Restart and verify
- Go to System → Restart to reboot the charger.
- After reboot, check Status → OCPP — should show ‘Connected’ with OCPP 1.
-
- In 22togo app, station should show ‘Online’.
If connection fails, verify server URL, identity, and auth token. Check OCPP logs for error details.
Charger capabilities
What this model supports with 22togo over OCPP.
-
OCPP 1.6J
-
Ethernet & Wi-Fi
-
Web & app commissioning
-
Authorization Key support
-
Smart charging profiles
Frequently asked questions
Does Elvi support single-phase installation?
The Elvi is a 22 kW three-phase charger. It requires a three-phase supply. For single-phase, consider the EVBox Livo (not in this guide).
Can I use the EVBox app for OCPP setup?
Yes. The EVBox app can configure Wi-Fi and OCPP settings. The web interface provides the same options with more detail.
Where is the Authorization Key field?
In the web interface: Settings → OCPP → Authorization Key. In the app: OCPP settings → Authorization Key.
Sources
These steps are based on public vendor documentation.