EVPoint · OCPP 1.6J
Not hardware-validated by 22togo Last verified 2026-11-12EVPoint EV7
Connect an EVPoint EV7 7.4 kW single-phase charger to 22togo over OCPP 1.6J.
The EV7 uses the same EVPoint web client as the rest of the range. Set the 22togo server address and UID in Backend Configuration, then confirm the OCPP connection in Charge Point Diagnostics.
Before you start
- A 22togo station record with its exact identity (Charge Point ID) and OCPP auth token.
- The OCPP server URL shown in the 22togo app for that station. It includes the station identity in the path.
- The charger installed, powered, and running a current firmware version.
- A phone or laptop with Wi-Fi, plus the EVPoint factory NFC card for EV11 and EV22 models.
Settings to enter
Use these values when configuring the charger's OCPP backend.
| Setting | Value | Notes |
|---|---|---|
| Protocol | OCPP 1.6J |
Select OCPP 1.6 JSON, not OCPP 2.0.1. |
| Server address | wss://<ocpp-host>/<identity> |
Use the exact URL from the 22togo app. The identity path segment is mandatory. |
| UID / Charge Point ID | <identity> |
Must match the 22togo station identity exactly, including case. |
| Authorization token | <ocpp_auth_token> |
Only if the charger firmware exposes an authorization token or password field. EVPoint's stock Backend Configuration screen exposes Server address and UID only; see the note below. |
| Primary interface | Wi-Fi, Ethernet, or GSM |
Set the interface that has a route to the internet. A secondary interface can be used as fallback. |
| Phases | 1-phase or 3-phase |
Match the electrical installation. EV7 is 1-phase; EV11/EV22/EV44 are 3-phase. |
Setup steps
Follow the steps in order. Restart the charger after changing backend settings.
-
1
Connect to the charger's Wi-Fi hotspot
On your phone or laptop, join the Wi-Fi network broadcast by the charger. The SSID is the charger serial number (printed on the label).
EV7 default Wi-Fi password: EVP-1234. EV11 and EV22 credentials are printed on the factory NFC card. Ignore any ’no internet’ warning — this is expected for a local hotspot.
-
2
Open the EVPoint web client
In a browser, open https://192.168.4.1/index.html and accept the certificate warning (the charger uses a self-signed certificate).
If the page does not load, try another browser (Firefox, Edge, Chrome, or Safari). Do not use a search engine — type the URL directly into the address bar.
-
3
Log in to the admin panel
Click the Admin panel menu item in the left sidebar, then enter the admin password when prompted.
EV7 default admin password:
admin. EV11 and EV22 admin credentials are on the factory NFC card. Change the default password after commissioning via the ‘Change admin password’ option. -
4
Configure the internet connection (Network Configuration)
- Click Network Configuration in the left sidebar.
- Under Network interface, select your primary connection method: Wi-Fi, Ethernet, or GSM.
- If Wi-Fi: click Set access credentials of Internet network, select your router’s SSID, enter the Wi-Fi password, and click Save.
- If Ethernet: ensure the cable is connected; the charger will detect it automatically.
- If GSM: click GSM interface, enter the APN, username, and password from your SIM provider. 6. Click Save and wait for the connection test to pass.
Confirm the charger has internet access (green checkmark) before configuring the OCPP backend. A secondary interface can be configured as fallback.
-
5
Set the 22togo server address and UID (Backend Configuration)
- Click Backend Configuration in the left sidebar.
- In Server address, enter the full OCPP WebSocket URL from the 22togo app (e.g.,
wss://ocpp.22togo.com/CHG-001). The identity path segment is mandatory — include the exact station identity. - In UID, enter the same station identity exactly as it appears in 22togo (case-sensitive).
- Ensure Protocol is set to OCPP 1.6J (not 2.0.1). 5. Click Save.
The UID must match the 22togo station identity exactly. Changing the UID does not change the charger serial number. If 22togo enforces a per-station auth token and your firmware exposes an Authorization token field, enter it here.
-
6
Restart and verify the OCPP connection
- Click Restart in the top navigation bar (or the Restart button on any page).
- After reboot, reconnect to the charger Wi-Fi and reopen the web client.
- Click Charge Point Diagnostics in the left sidebar.
- Check OCPP network info — it should show ‘Connected’ with the correct server URL and negotiated protocol (OCPP 1.6). 5. In the 22togo app, the station status should change to ‘Online’.
If the charger stays offline, re-check: server URL (must include identity path), UID (exact match), internet interface (green checkmark), and charger clock (NTP sync). Charge Point Diagnostics shows the exact error.
-
7
Optional: add RFID cards for local authorization
- Click NFC Configuration in the left sidebar.
- Click ADD NEW.
- Tap the RFID card on the reader area (front of the charger). The card UID will appear in the list. 4. In the 22togo app, go to the station’s RFID tags and add the same card UID to enable local authorization.
RFID authorization works alongside 22togo app and OCPP authorization. The charger checks local list first, then falls back to OCPP.
-
8
Optional: configure power limits and CT clamp (Configuration of External Devices)
- Click Configuration of External Devices.
- For CT clamp: set CT ratio (e.g., 100:1 for a 100A CT), CT phase mapping (which phase the CT is on), and Main fuse limit (your grid fuse rating in amps).
- For MID meter: enter the meter serial and configure the Modbus address.
- Set Device current limit (max current the charger will offer, in 0.1A increments — e.g., 320 = 32A). 5. Save and restart.
Incorrect phase or CT settings can cause faults or reduced charging power. OCPP smart charging uses Default, TxProfile, and MaxProfile schedules on top of these limits.
Charger capabilities
What this model supports with 22togo over OCPP.
-
OCPP 1.6J
-
Web-based commissioning
-
RFID / NFC authorization
-
Wi-Fi, Ethernet, and 4G
Available interfaces depend on the model and hardware variant.
-
OCPP smart charging profiles
-
External CT / load balancing
Requires a compatible CT clamp and correct configuration.
Frequently asked questions
Is the EVPoint EV7 single-phase?
Yes. The EV7 is a 7.4 kW single-phase charger. Make sure the charger and the 22togo station are configured for a single-phase installation.
What is the EV7 Wi-Fi password?
The default EV7 Wi-Fi password is EVP-1234. The default admin password for the web client is admin. Change both after commissioning.
Can the EV7 use three-phase power?
No. The EV7 is the single-phase model in the EVPoint range. Use an EV11 or EV22 model for three-phase installations.
Sources
These steps are based on public vendor documentation.