Wallbox · OCPP 1.6J

Not hardware-validated by 22togo Last verified 2026-11-12

Wallbox Pulsar Plus 22

Connect a Wallbox Pulsar Plus 22 kW three-phase charger to 22togo over OCPP 1.6J.

22 kW 3-phase 1 × Type 2 OCPP 1.6J

The Pulsar Plus 22 uses the Wallbox app or portal. Configure the OCPP Server, Charge Point ID, and OCPP Auth Password in Settings → Charger → OCPP, then save and verify connection.

Before you start

  • A 22togo station record with its exact identity (Charge Point ID) and OCPP auth token.
  • The OCPP server URL shown in the 22togo app for that station (including identity path).
  • The charger installed, powered, and connected to the internet (Wi-Fi or Ethernet).
  • The Wallbox app (iOS/Android) or access to the Wallbox portal (portal.wallbox.com).

Settings to enter

Use these values when configuring the charger's OCPP backend.

Setting Value Notes
OCPP Server wss://<ocpp-host>/<identity> Use the exact URL from the 22togo app. Must include the identity path segment.
Charge Point ID <identity> Must match the 22togo station identity exactly.
OCPP Auth Password <ocpp_auth_token> Enter the per-station auth token from 22togo. Wallbox calls this 'OCPP Auth Password'.
OCPP Version OCPP 1.6J Select OCPP 1.6 JSON.
Network Wi-Fi or Ethernet Configure Wi-Fi (via app) or Ethernet before enabling OCPP.

Setup steps

Follow the steps in order. Restart the charger after changing backend settings.

  1. 1

    Connect charger to internet

    1. Power on the charger.
    2. In the Wallbox app, go to Settings → Charger → Network.
    3. For Wi-Fi: select your SSID, enter password, and connect.
    4. For Ethernet: plug in cable; DHCP is automatic. 5. Verify the app shows ‘Online’ status.

    Wallbox chargers must have internet access before OCPP can be enabled. The app is the easiest way to configure Wi-Fi.

  2. 2

    Enable OCPP in the Wallbox app

    1. In the app, go to Settings → Charger → OCPP.
    2. Toggle OCPP Enabled to ON.
    3. Set OCPP Version to OCPP 1.6J.
    4. In OCPP Server, enter the full 22togo WebSocket URL including identity path (e.g., wss://ocpp.22togo.com/CHG-001).
    5. In Charge Point ID, enter the exact station identity from 22togo.
    6. In OCPP Auth Password, enter the OCPP auth token from 22togo. 7. Tap Save.

    The app may require a charger restart after saving OCPP settings. The ‘OCPP Auth Password’ field is the per-station token from 22togo.

  3. 3

    Alternative: Configure via Wallbox portal

    1. Log in to portal.wallbox.com.
    2. Select your charger.
    3. Go to Configuration → OCPP.
    4. Enter the same values: Server URL, Charge Point ID, Auth Password, Version 1.6J. 5. Save and restart the charger from the portal.

    The portal provides the same settings as the app. Useful if you prefer a larger screen.

  4. 4

    Verify connection

    1. After saving, the charger will restart automatically (or restart manually via app/portal).
    2. In the app, go to Status → OCPP — should show ‘Connected’ with protocol OCPP 1.
      1. In 22togo app, station should show ‘Online’.

    If status is ‘Disconnected’, check the server URL (must include identity path), Charge Point ID (exact match), and Auth Password. Wallbox logs are available in the portal.

Charger capabilities

What this model supports with 22togo over OCPP.

  • OCPP 1.6J

  • App & portal commissioning

  • Wi-Fi & Ethernet

  • OCPP Auth Password support

  • Smart charging profiles

  • Dynamic load balancing

    Requires Wallbox Energy Meter or compatible CT clamp.

Frequently asked questions

Is the Pulsar Plus 22 three-phase?

Yes. The 22 kW Pulsar Plus is a three-phase charger (max 32A per phase). Requires a three-phase supply.

Does the Pulsar Plus 22 have Ethernet?

No. The Pulsar Plus uses Wi-Fi only. For Ethernet, use the Commander 2 or Pulsar Pro.

Can I use three-phase load balancing?

Yes. With the Wallbox Energy Meter (three-phase version) or compatible CT clamp, three-phase dynamic load balancing works via OCPP.

Sources

These steps are based on public vendor documentation.